Krzysztof Sornek; Rafal Damian Figaj; Karolina Papis-Frączek · 10.1016/j.applthermaleng.2024.124515 https://doi.org/10.1016/j.applthermaleng.2024.124515
Applied Thermal Engineering
Development and tests of the novel configuration of the solar chimney with sensible heat storage Krzysztof Sornek; Rafal Damian Figaj; Karolina Papis-Fraczek Heating, ventilation, and air conditioning systems account for a significant part of the energy usage in buildings and are primarily responsible for greenhouse gas emissions and operating costs. These can be lowered by the adoption of solar energy. This paper presents the developing and testing of a novel solar chimney with sensible heat storage. The thermal performance and potential contribution of the developed thermal chimney to decreasing residential buildings energy consumption in Polish climate conditions is investigated. The developed solar air chimney is composed of a novel accumulation material that allows for sensible heat storage. Solar radiation can heat the accumulation layer during the day and the stored energy can be used to preheat the ventilation air. The prototype of the solar chimney was tested in laboratory conditions using a dedicated experimental rig. Furthermore, numerical calculations were performed using TRNSYS software, where a validated dynamic numerical model was developed to simulate the performance of the device. The results show that airflow direction, volume, and the number of heated walls significantly impact the power transferred from the solar chimney walls to the air. The maximum power transferred from the solar chimney walls to the air per unit of surface varied from 360.2 W/m2 (when all walls were heated) to 672.4 W/m2 (when only one wall was heated). The validated model underestimates the outlet air temperature of the solar chimney by a maximum of 0.39 °C on average basis and shows that the increase of air temperature between −10 and 20 °C at 1000 W/m2 determines a decrease of 12.5 % of the thermal output. The obtained results allow one to highlight that the proposed solution can be considered as a replacement for typical brick chimneys located on roofs or as a thermal storage wall.
Building ventilation
Experimental
Numerical / CFD
Thermal storage / PCM
2024
Applied Thermal Engineering
no
2024-10-01 12:00:00 00001720
development and tests of the novel configuration of the solar chimney with sensible heat storage
2024
Applied Thermal Engineering
Krzysztof Sornek; Rafal Damian Figaj; Karolina Papis-Frączek
10.1016/j.applthermaleng.2024.124515
Abstract
Heating, ventilation, and air conditioning systems account for a significant part of the energy usage in buildings and are primarily responsible for greenhouse gas emissions and operating costs. These can be lowered by the adoption of solar energy. This paper presents the developing and testing of a novel solar chimney with sensible heat storage. The thermal performance and potential contribution of the developed thermal chimney to decreasing residential buildings energy consumption in Polish climate conditions is investigated. The developed solar air chimney is composed of a novel accumulation material that allows for sensible heat storage. Solar radiation can heat the accumulation layer during the day and the stored energy can be used to preheat the ventilation air. The prototype of the solar chimney was tested in laboratory conditions using a dedicated experimental rig. Furthermore, numerical calculations were performed using TRNSYS software, where a validated dynamic numerical model was developed to simulate the performance of the device. The results show that airflow direction, volume, and the number of heated walls significantly impact the power transferred from the solar chimney walls to the air. The maximum power transferred from the solar chimney walls to the air per unit of surface varied from 360.2 W/m2 (when all walls were heated) to 672.4 W/m2 (when only one wall was heated). The validated model underestimates the outlet air temperature of the solar chimney by a maximum of 0.39 °C on average basis and shows that the increase of air temperature between −10 and 20 °C at 1000 W/m2 determines a decrease of 12.5 % of the thermal output. The obtained results allow one to highlight that the proposed solution can be considered as a replacement for typical brick chimneys located on roofs or as a thermal storage wall.
Abstract by the authors, reproduced under the CC BY-NC-ND 4.0 licence. Original publication via the link below.
Open source
1-s2.0-S1359431124021835-main-1.pdf